How to Lay Vinyl Plank Flooring? | Simple 8 Steps
Vinyl plank flooring is easy to install and gives a very innovative look to your space, and that’s the reason why most people install vinyl plank flooring in their homes. Also, it is moisture resistant and can easily get installed in the areas like the kitchen, or bathroom. Although it is easy to install, some people hire professionals, and some people wondering to know How to Lay Vinyl Plank Flooring in their houses.
However, there is no need to hire professionals and waste a lot of money. You can do it all by yourself and get it installed without shelling out the money. It’s just a matter of a few hours and your space will gain a whole ravishing look when you lay vinyl plank flooring. All you need is just to grab some tools, cut the Vinyl Flooring and get them installed.
Some Easy Steps On How to Lay Vinyl Plank Flooring?
Here are some quite easy and simple steps to give you an understanding of how to actually lay vinyl plank flooring all by yourself. There will be the need for some tools and materials so that you can easily get them installed and allow your space to give a luxurious look. If you follow the steps properly for How to Lay Vinyl Plank Flooring? you see that installation of vinyl plank flooring by yourself is not much grueling.
1. Collect the Material and Tools to Lay Vinyl Plank Flooring
First thing first, before you are going lay vinyl plank laminate flooring in your living place, you will need the following material and tools to make your task much easier. Make sure you have all the items given below with you when you start the installation.
- Hammer
- Measuring Tape
- Flat pry bar
- Utility Knife
- Fine-tooth saw
- Straightedge
- Drawbar tool
- Nail Set
- Vinyl flooring planks
- Sand Paper
- Concrete Patcher
- ¼ inch spacer
2. Remove All the Accessories First
When you feel ready with the tools mentioned above for How to Lay Vinyl Plank Flooring? There is another mandatory thing that needs to be done before the installation. In the very first place, plan how you want to situate the flooring Dubai at your place. When you are done with the planning, start removing all the trim molding, making contact with the floor for ease of installation.
Generally, these trim moldings are attached to the walls with the help of some very sharp nails. So, you have to do this task with much care and it will be better if you use a flat pry bar to remove these trims. Also, if you succeed in the proper removal of trims, i.e. trims are in condition even after removal. You can set them aside for reuse purposes after getting the installation done of vinyl plank flooring.
3. Prepare The Floor Before Installation of Vinyl Plank Flooring
After the removal of trim molding, now it’s time to prepare your floor to lay vinyl plank flooring over it. Of course, vinyl plank flooring gets installed over the already existing floor, but the surface should be flat and smooth enough. So, if you see any high spots over there, try to sand them down, making an even surface.
Most often, people like to have vinyl SPC flooring over the concrete flooring, so if there are any cracks over its surface, fill them up with the concrete patcher. And, if you are going to lay the flooring over the plywood subfloor, and there is any depression, fill them up with the floor-leveling compound. In this way, your floor gets ready to have vinyl plank flooring over it.
4. Test the First Row and Cut the Planks
In order to cut the planks properly, it is essential to test the first row by laying it on the floor so that you could get an idea about the layout and your cutting task will become easy. Test the row by leaving the space almost ¼ inches from the wall. Proper cutting of planks is a mandatory thing when you are going to lay vinyl plank flooring in order to give an adorable look to your space.
For the cutting of planks, use a utility knife and run it slightly over the face of the plank several times. Don’t try to cut it in one row or you may get yourself injured. Vinyl planks are very slippery so cut them with great care. Then, flip the plank and repeat the same procedure. Now, fold it and it may snap off into two pieces by itself, easily.
5. Install the Planks on to the Floor
How to Lay Vinyl Plank Flooring? vinyl planks are usually getting attached to each other edge-to-edge or end-to-end by following a tongue-and-groove or fold-and-lock system so that there will be the proper installation of flooring at your place. Now, vinyl plank flooring by installing the first plank on the subfloor. Make sure the first plank lies flat and the second plank lies at an angle and is placed into the first plank’s receiving trench.
Fold the second plank until it gets attached to the first plank and gets locked. When the first row gets installed, lay all the other rows in the very same manner. Keep in mind that the end joints of planks should be stumbled enough, and should be almost 6 inches away from the end joints of the previous row.
6. Cut and Fit Across the Ledges
If there are any obstacles, i.e. door frames or any floor ducts, cut the planks according to the shape easily with the help of a utility knife. After cutting the plank into the desired shape, get it fit across the ledge by holding the cut-out plank in the upward direction. Then, start to fold it down until it gets locked into the previous/adjoining plank.
People might get confused about these ledges while installing the vinyl planks by themselves. Well, there is no need to worry about that, and now you know how easily you can lay vinyl plank flooring even across the ledges.
7. Install the Last Row of Vinyl Plank Flooring
After you have done the installation of your entire space, now it’s time to install the last row of vinyl plank flooring and get the task done. Cut the last row of planks in the narrow strips so that there will be a gap of almost ¼ inches between the plank and the wall. You can cut them with the same process, i.e. slightly running the knife over the plank several times.
Hold the planks tightly against the adjacent planks and make sure to lock them up with the already installed planks so that it may give a proper finishing and here you are almost done to lay vinyl Rubber flooring in your place.
8. Install the Trim Molding and Allow Your Floor to Add up the Value
Now, you have successfully installed the complete vinyl plank flooring, so it’s time to reinstall the trim molding across the perimeter of your room to give a nice, elegant finishing. Use a nail set and a hammer to install them. Hammer could damage the trim, so do this step with soft hands and with much care.
These trim molding will hide the spacing that you left between the flooring and the wall, thus allowing your floor surface to add some value to your property by its brand new shine and adorable appearance.
To Curl Up
At the end of this article, it is safe to say that you are going to install the vinyl plank flooring in your space on your own without wasting a lot of money by hiring some professionals. Follow these simple steps in the proper way to How to Lay Vinyl Plank Flooring and let your place gain an appealing look.