How to Remove Laminate Flooring? | Simple & Worthy Methods

How to Remove Laminate Flooring

 

No doubt, most people like to install laminate wood flooring in their home space just because it can perfectly mimic the look of hardwood flooring. In addition, it is much affordable and makes the space look much more adorable by its appearance. But, unfortunately, it does not last as long as the real hardwood flooring. The lifespan of laminate Flooring tiles is generally 15 to 25 years, but it also depends on foot traffic.

How to Remove Laminate Flooring? If it is installed in a high-traffic area, it could come to its end in only 10 years, and if it is installed in a low-traffic area, it could last up to 30 years. However, real hardwood flooring can last much longer than this by just having a proper refinishing over its surface from time to time.

On the other hand, if the upper layer of flooring gets damaged, you need to replace the whole of it. At this point, availing of professional services comes to mind. But you can do this task on your own by following the steps given below in this article.

Essential Tools & Methods For How to Remove Laminate Flooring?

Tools You Will Need to Remove the Laminate Flooring

 

For the removal of the flooring Dubai from your space, first get yourself ready with all the necessary tools which are used in the removal process, so that you could easily get this task done. Check if you have a pry bar, pliers, mallet, heat gun, or floor scraper. Along with all these necessary pieces of equipment for How to Remove Laminate Flooring, don’t forget to take precautionary measures so that you don’t get yourself injured during this process.

Take a dust mask, safety gloves, and safety glasses. However, if you don’t have any of them, you can easily get them from any hardware store. Or, you can even rent them from that store for some time, and get them returned after the completion of this very task.

Get Your Room Prepared For the Removal of Laminate tiles Flooring

First thing first, you have to get your room prepared for the proper removal of the laminate floor. Remove all the furniture out of the room to make your work easy. Then, remove all the baseboards around the perimeter of the room, which you might have installed for an adorable look at your flooring.

Get Your Room Prepared For the Removal of Laminate Flooring

 

You can easily get them removed with the help of a pry bar. Be careful while on their removal, if you want to reinstall them with another flooring like SPC flooring. In addition, there will be some planks that must be glued down, so it will be better if you do mopping over the floor before removing it. Mopping will soften the glue and make those planks easy to get removed.

Start Tearing Off Your Laminate Wood Flooring

When you are done preparing your room for the removal of the laminate floor, then start to tear it off. Tearing off means to start removing it. It is recommended to start from the corner or wall piece by using the gap between the wall and the board so that you can easily do this task with the simple use of a pry bar.

Set the pry bar underneath the plank and lift it by 30-45 degrees. You have to continue this step underneath every plank so that the plank loses its bond with the subfloor, and easily gets removed.

Don’t forget to wear your safety gloves, safety glasses, and a dust mask during this How to Remove Laminate Flooring whole task. Now, if there comes any plank which is glued down, then the best way to remove them is to apply the constant heat over them. Use a heat gun for this process above a few inches from the surface of your laminate flooring. Then, remove that plank by the same use of a pry bar.

Remove All the Adhesives Left Behind

Remove All the Adhesives from floor

 

After the removal of all the planks of your tiles flooring, there will be some adhesives left over. You will see on the subfloor, which obviously, needs to be removed. That adhesive left over is of the glued planks. For the removal of it, a floor scraper is the best tool.

If the subfloor is made up of concrete, then there will be a lot of adhesive remaining. Start running its blade (should be sharp enough) over the subfloor at an angle of 30-45 degrees to get rid of that glue/adhesives. If you notice that the blade is becoming dull, replace it quickly with the sharp one.

Although this step is going to take time, it will be worth it when you get a neat and clean floor. On the other hand, if the subfloor is made up of wood flooring, then it is recommended to use the orbital sander for the glue removal process.

Clean the Subfloor And Prepare it For the Next Installation

After all the removal process has been done, clear up all the mess that has been created during the completion of this task. It will be better if you do vacuuming or mopping (a basic cleaning process) of your subfloor. In this way, it will get the next installation of flooring easily, and create a whole ravishing look of your place.

To Curl Up

At the end of this article, I will highly recommend following these simple and easy steps for How to Remove Laminate Flooring from your home space. If you follow them properly, there will be no need of hiring professionals for this task, but you, yourself can easily get this task done in no time and get your floor prepared for the next installation. So that your space will gain an attractive look, once again.

Leave a Reply

Your email address will not be published.

Fill out this field
Fill out this field
Please enter a valid email address.
You need to agree with the terms to proceed

Menu