How to Lay Laminate Flooring? | DIY-Guide (2022)

 

How to Lay Laminate Flooring

Flooring is, no doubt, a fundamental piece of statement in your entire home decor. With so many available options in the market, you must want to go with some flooring that can fulfill your all requirements. Laminate flooring is much durable and also scratch-resistant, hence, most people like to know How to Lay Laminate Flooring in their homes.

But people do this installation process of laminate flooring by hiring professionals. Well, there is no need to hire professionals if you are going to install laminate flooring in your living place. It is really very easy to lay laminate flooring in your living space on your own by following some steps that you are going to read in this article.

Some Easy Steps On How to Lay Laminate Flooring?

Given below are some easy and simple steps to lay laminate flooring at your place and make it look more adorable. Actually, you will find its installation much more fun, i.e. getting the puzzle pieces together. It is easy to clean and install you just need to follow the steps properly for How to Lay Laminate Flooring? as mentioned below.

Some Item You Will Need To Lay Laminate Flooring

1. Some Item You Will Need To Lay Laminate Flooring

There are some materials and equipment that you will need to install laminate vinyl flooring. Make sure you have all the given items below before starting the installation process.

  • A Knife
  • Hammer
  • Tapping block
  • Laminate flooring
  • Scrap wood spacer
  • Rubber Mallet
  • Pencil
  • Speed Square
  • Chalk box
  • Tape Measure
  • Straightedge
  • Jigsaw

 

Now you are ready to lay laminate flooring in your home area.

2. Prepare Your Subfloor

Before you go out to know How to Lay Laminate Flooring in your space. Let me tell you that it requires a properly prepared sub-floor. So, first thing first, get your subfloor prepared, i.e. smooth, flat, and clean. Moreover, a simple sheet of foam is enough to lay under the laminate Wooden flooring as a base so that it can get installed properly, enhancing the beauty of your home decor.

In addition, if the subfloor is uneven or damaged, you might need to install plywood first, and then a sheet o foam to make it even and smooth. Then, remove all the baseboards, and get the perimeter of your room trimmed. In the last, vacuum the area properly, and then start your installation process.

3. Test the Layout by Arranging the Planks

After you have done preparing the subfloor, now in the very first place, check the layout of your hardwood flooring and see how are you going to arrange them. Arrange the planks without getting them locked just to test. Be careful while testing because if they got locked by mistake it can damage the edge of planks, and your whole installation process will get difficult to be done and look messy.

Arrange the length of the planks end to end and try sensing the layout. As soon as you understand the layout, better to start the installation immediately. But first, pull all the planks back and stack them in the corner of your room.

4. Start Installing the First Row of Laminate Planks

First of all, trim the tongues from all the boards that might edge the first wall. You can do this step with the help of a knife or a jigsaw, but make sure you do this step with much care so that you don’t get injured.

Now, when you start installing the first row of planks, check that the trimmed edges should be lying against the wall. Keep almost ¼ space from the wall while installing the planks and make sure that the seamed edge faces out. Maintain that space/gap by placing the scrap wood spacer between the wall and the plank.

After laying the length of planks, sing them down by tapping over them with a hammer or tapping block so that they can get locked properly. Make sure there will be no gap between the end joints of the laminate outdoor flooring.

5. Finish Installing the First Row of Laminate Planks

If you want to know How to Lay Laminate Flooring? then follow these steps with keen attention. Now when you reach the end of the very first row of the laminate planks, the last plank will be of full length. All you need to do is just to measure the remaining length of the floor and install that plank thereby, trimming down its extra tongue.

That remaining piece which you trimmed down will be the first length plank of the second row. So keep it aside and finish the first row by locking the ends of the last planks. In this way, you securely finish the installation of the first row with a fine touch.

6. Plan And Continue Laying More Rows of Laminate Planks

Every last piece of the plank will be cut down and will be used as the first plank of every new row. Now, for the next rows, hold these planks at the angle of 45 degrees and insert the longest plank into the groove of planks in the proceeding rows. Join all the planks together and get them locked in a very secure manner.

Keep in mind that the appearance of these rows should be like sawtooth or weaved so that they could make the whole space look more attractive. You must know everything about laminate flooring before the installation it will be better if you keep the length of each plank, not shorter than 16 inches, to give a unique look and to give stability to the flooring.

7. Finish this process by installing the Last Row of Laminate Planks

When you are going to finish your installation process by inserting the last row, you will see there will be ripped planks left over. The installation process of the last row can be tricky because you are going to insert it tight against the wall.

Make sure you tightly insert the last row and then complete this process by removing the spacers from the gap between the wall and planks. Insert the baseboards along the room’s perimeter. Then, do some molding in order to hide that gap, and allow your floor to give an elegant look to your space by clearing all the mess and sweeping it once.

Some Tips You Need to Know For the Cutting of Laminate Planks

Some Tips You Need to Know For the Cutting of Laminate Planks

After knowing all the installation process, you now must be concerned about the cutting of planks very much, obviously. So, here are some tips that will help you to cut them down properly and make your space look beautiful by allowing you to lay laminate flooring.

  • Use a knife with great care to cut the planks because they are very thin
  • Don’t get panicked while cutting process
  • If you are not okay with a knife, use a table saw to cut the planks. They give a perfect cut.
  • You can also use a fine-tooth saw to cut the planks with less chipping of the laminate surface
  • Always cut the planks from the backside to avoid chipping
  • If you are using a table saw to cut the planks, make sure you face them up because it cuts them through the bottom.

To Sum Up

These were some easy and simple steps of How to Lay Laminate Flooring in your space, which, when followed appropriately, will result in the perfect installation of flooring in your house, making it look much more appealing.

Leave a Reply

Your email address will not be published.

Fill out this field
Fill out this field
Please enter a valid email address.
You need to agree with the terms to proceed

Menu